Broadcast Tools WVRC-8 Spezifikationen PDF herunterladen (Seite 4)

e-mail:

[email protected]

voice:

360.854.9559

fax:

866.783.1742

WVRC-8 Installation and Operation Manual

INTRODUCTION

Thank you for your purchase of a Broadcast Tools® WVRC-8, Eight Channel WEB and Voice

Dial-up Remote Control System (referred to as the WVRC-8 throughout this manual). We’re confident

that this product will give you many years of dependable service. This manual is intended to give you all

the information needed to install and operate the Broadcast Tools® WVRC-8.

SAFETY INFORMATION

Only qualified personnel should install Broadcast Tools® products. Incorrect or inappropriate use

and/or installation could result in a hazardous condition.

Broadcast Tools, Inc., is unable to support NON-Broadcast Tools software, hardware or NON-Broadcast

Tools computer/hardware/software problems. If you experience these problems, please research your hard-

ware/software instruction manuals or contact the manufacturers technical support department.

Only qualified technical personnel should install the WVRC-8. Any attempt to install this device by a

person who is not technically qualified could result in a hazardous condition to the installer or other per-

sonnel, and/or damage to the WVRC-8 or other equipment. Broadcast transmitters can operate at voltages

that are potentially lethal. Please ensure that proper safety precautions have been made before installing this

device. If you are unfamiliar with this type of equipment, please contact a properly qualified engineer to

handle the installation and setup of the WVRC-8.

Broadcast Tools® Products, as with any electronic device, can fail without warning. Do not use this

product in applications where a life threatening condition could result due to failure. Serious injury or

death can occur if a command channel is activated while you are performing maintenance on your

equipment. If you are performing maintenance on your equipment, you should press the “PGM” button

on the front panel of your WVRC-8 forcing the unit in to local mode. The “PGM” LED will illuminate.

Local mode prevents the unit from performing relay commands.

For additional safety, it is strongly recommended that, in addition to setting the WVRC-8 in to OP/PGM

mode, the remote/local switch on any transmitter or high voltage equipment also be set to local mode.

While the WVRC-8’s relays are physically capable of handling 250 VAC, this practice is extremely

dangerous and should never be attempted. The pluggable euroblock screw terminals are not designed to

shield humans from potentially dangerous voltages. Contact with high voltages can cause serious injury

or death. The maximum recommended voltage for the WVRC-8 is 30V. Switching of high voltages should

only be done external from the WVRC-8 and in a manner that isolates the voltages from accidental con-

tact with humans.

WHO TO CONTACT FOR HELP

If you have any questions regarding your product or you need assistance, please contact your

distributor from whom you purchased this equipment.

If you would like more information about Broadcast Tools® products, you may reach us at:

Broadcast Tools, Inc.

131 State Street

Sedro-Woolley, WA 98284-1540 USA

Voice: 360.854.9559

Fax: 866.783.1742

Internet Home Page: www.broadcasttools.com

E-mail: [email protected]

THANK YOU FOR CHOOSING

BROADCAST TOOLS® BRAND PRODUCTS!

CAUTION!

Broadcast Tools®

Products, as with any

electronic device, can

fail without warning.

Do not use this product

in applications where a

life threatening condition

could result due to failure.

NOTE:

This manual should be

read thoroughly before

installation and operation.

WEBSITE:

Visit our web site for

product updates and

additional information.

1 2 3 4 5 6 7 8 9 ... 40 41

Kommentare zu diesen Handbüchern

Keine Kommentare

Broadcast Tools WVRC-8 Spezifikationen Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fernbedienungen Broadcast Tools WVRC-8